For UK service,
Please visit http://appuk.co.uk

T-1000 Options and Accessories


Options and Accessories for the T-1000

Although the T-1000 is extensively equipped with many "built in" options, a full range of auxiliary options and equipment can easily be added for special purpose packaging or to improve your packaging operation.

Funnels, Standard and Custom: Order funnels that are in stock at all times with sizes ranging from a 1" opening to a 7" opening. Custom funnels are also provided to facilitate loading. Having the proper funnel and bag size for your product is very crucial to an efficient operation.

AF-10 Accumulating Funnel: Pneumatic gate increases the speed of automatic operations by "staging" the product immediately above the bag opening. When the bag is ready to receive the product, the gate opens, enters the bag, and maintains the bag opening to reduce product spills.

CF-10 Counting Funnel: Add a photo array to the AF-10 funnel for inline bagging operations. Counts product as it enters the funnel; pneumatic funnel causes separation between counts for continuous feed operations.

LS-10 Load / Support Shelf: Supports the bottom/back of bag during loading of heavier or bulkier products. Pneumatically operated, adjustable shelf provides support and takes the initial impact of heavier products dropping into the bag. Shelf tilts downward after sealing, dropping product from the shelf. Available in various length for longer bag sizes.

LSV-10 Vibratory Shelf Attachment: "Taps" the bag to settle product to the bottom of the bag. Pneumatic operation with speed controls. LS-10 Option must be previously installed or purchased with the vibratory shelf attachment.

LC-10 Light Safety Curtain: An OSHA approved safety device that restricts the cycle operation of the bagger when the optical detection field is obstructed. LC-10 option is recommended when the funnel is removed and the product is loaded directly into the bag. Increase production by 40% by turning on the "auto" feature to cycle the bagger on the trailing edge of the light curtain input signal. Lockout key is provided to prohibit bypassing the safety feature. Excellent option for hand loading operations.

DF-10 Diverting Funnel/Bag Counting Option: As finished bags are sealed and dropped from your bagger, they can be counted and redirected at the end of each preset count. With a two box system, the bags are directed into "Box A" until the final count is reached. Then the diverter rotates, directing the bags into "Box B" allowing the operator time to remove, seal and replace "Box A". Includes diverting/rotating attachment, photo array, brackets and counter controls. (UF-2000 Incline Conveyor sold separately.)

PT-10 Partition Table Attachment: Stainless steel partitioned utility table keeps products separated for manual kit packaging. Two sizes available depending upon size and quantity of product. Adjustable tilt and height to fit over bagger

LB-10 Label Applicator Attachment: Apply preprinted labels inline while bagging. Labels are accurately dispensed onto the bag from an air vacuum grid with +/- 1/32" dispensing accuracy. Also Print and Apply labels with our thermal transfer printer/label applicator. Print up to 305dpi on labels from 1/2" x 1/2" up to 4" x 6". CD-10

Compact Disc Loader: With the CD Loader option, the T-1000 packages compact discs at a rate of up to 70 packages per minute. Package into tamper evident poly bags, either printed or nonprinted Significantly reduce packaging costs over jewel cases or sleeves.

PB-20 Dual Optical Palm Buttons: OSHA approved safety device. Two optical "no-touch" buttons must be pressed simultaneously to initiate the cycle operation of the bagger. If the two sensors are not pressed at the same time, the bagger will not cycle, ensuring that fingers or hands cannot be in the seal area. Recommended when no funnel is present.

SP-10 Level 1 Spare Parts Kit: Kit contains day to day normal wear items. PTFE sheet, filter, fuses, seal rubber, and heater cartridges identifies some items in the kit.

SP-20 Level 2 Spare Parts Kit: Additional items not projected to fail, but due to the cost of loss of production, are required to prevent downtime. Valves, cylinders, circuit boards, and a touch screen are some of items included in this kit.

FS-10 Flat Seal Assembly: Decreases the possibility of wrinkles in the seal area while increasing seal integrity. Pneumatically operated opposing "fingers" pull each side of the bag taught above the seal area to flatten the seal area.

BF-10 Bag Deflator: Removes excess air from the bag. Sponge or rubber loop deflators push the air out just prior to sealing.

BV-10 Barcode Verifier: Verifies that barcodes on preprinted or thermally printed bags are readable and stops the cycle operation when a non-readable barcode is detected.

More Options

AD-10 Point of Use Air Dryer: Filter 99% of liquids from your plant air with this dryer component. Liquids are then automatically drained before entering the pneumatic system increasing component life.

BO-10 Bag "Out" Sensor: Detects the last bag off the roll and shuts down the bagger, while alerting the operator of the fault condition.

BO-20 Bag "Open" Sensor: (AF-10 Funnel required.) Detects whether the bag has properly blown open prior to the product entering the bag.

CB-10 Compartment Seal Option: Separate two products in one bag by creating a seal between two compartments. After the first product is loaded, press the foot switch to seal the first product in the bag. Then load the second product, and press the foot switch to index the bag and seal the bag a second time above the second product. The bag is then detached and another bag is indexed into the loading position.

FD-10 Single 3-1/2" Floppy Disk Loader: With the Floppy Disk Loader option, the T-1000 packages 3-1/2" floppy disks at a rate of up to 60 packages per minute. Cartridge tray holds up to 300 floppy disks. Load floppy disks while bagging. Loader can be quickly removed to package manuals, case drivers, instruction sheets or any other loose items such as screws, keys or kits.  

IF-10 Insert Funnel: For products affected by air flow, an insert funnel provides a solution. After the bag has been blown open, the funnel enters the bag, holding it open so air can be decreased or shut off. The funnel enters past the seal area decreasing the potential of seal contamination. This is good for granular type products.

OFS-10 Output Fault Signal: Signal is provided to advise third party equipment that a fault condition (i.e.: out of bags, jam detection, printer error) is present on the T-1000 bagger and to cease production operations. Audible or visual signals can also be provided to alert the operator.

QC-10 Quick Roll Change Option: Additional roll shaft and roll chucks. By having a full roll shafted, the operator can perform roll changes quickly and immediately when the bagger is out of bags.

TS-10 Trim Seal Assembly: Trims excess film from bag above seal to enhance the appearance of the package (retail products).

TW-10 Twin-Seal Option: Automatically seals the bag a second time, 3/4" from the first seal to increase bag integrity.

VA-10 Vacuum Bag Opening Assembly: When air flow is not sufficient to open the bag, or when air cannot be used to open the bag, vacuum tips do the job. Tips protrude to the bag and retract pulling the bag open. Air flow can be shut off for products affected by air flow.

Products

Items 21 to 30 of 58 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

List  Grid 

Set Descending Direction
  1. T-1000 Funnels

    T-1000 Funnels

    Product Code:
    • TO-T1-FU
    Standard funnels for T-1000. Choose from any size funnel based on your bag size or order the complete kit of all sizes. If this is your first time attaching a funnel on your equipment, you will need to purchase the correct hardware kit. Please order TO-T1-FU-HWKIT. If you have an existing funnel on your equipment and are purchasing a new size, this kit is not necessary. Please see all documents below for further detail. Learn More
  2. T-1000 Flat Seal Assembly

    T-1000 Flat Seal Assembly

    Product Code:
    • TO-T1-FS
    This option decreases the possibility of wrinkles in the seal area while increasing seal integrity. The flat seal assembly is pneumatically operated using opposing "fingers" which pull each side of the bag above the seal area to assist in flattening the seal area. FS-10 function is based on a pivoting set of fingers which extend downward to pull the sides of the bag. The fingers pivot by use of a cylinder controlled by a single solenoid valve. FS-20 function is based on TWO motions, both downward similar to the FS-10, but also outward. This option has two different sets of cylinders, one to pivot the fingers downward and another type of cylinder to pull the fingers outward and are controlled by two solenoids. This function is often used in applications where both the appearance and function of the seal is critical. This option reduces the greatest amount of the wrinkles are folds. Another function of this version is that the finger are already in the bag when the product is being loaded preventing the perfs from separating at the edges which cause the fingers to miss the sides. FS-30 functions exactly like the FS-10, but has heavy duty fingers and mounting blocks. This version is great for heavy industrial bags to increase the strength and improve the appearance of the seal for heavier parts. For all versions, you must determine whether your bagger is a Standard Frame, Drop Frame or Extended Drop Frame. To determine which configuration you have, you can simply measure the distance from the Feed Point of the bags (from the nip rollers) to the Seal Point. The following measurements are provided for each configuration: Standard Frame distance: 3 inches Drop Frame distance: 5 inches Extended Drop Frame distance: 7 inches (6.5 inches on wide baggers) Note: please review the photo which illustrate how to measure the distance from the feed point to the seal point. Disclaimer: APP cannot guarantee that all wrinkles or folds will be removed. More importantly, APP cannot guarantee that the bags will not leak air, either from the bagger seal or the seal which produce the bag. Learn More
  3. Horizontal Drop Plate Assembly

    Horizontal Drop Plate Assembly

    Product Code:
    • TO-T1-HLS
    Pneumatically operated "drop" plate to remove bag from sealing area. Learn More
  4. T-1000 Light Safety Curtain

    T-1000 Light Safety Curtain

    Product Code:
    • TO-T1-LC
    An OSHA approved safety device that restricts the cycle operation of the bagger when the optical detection field is obstructed. LC-10 option is recommended when the funnel is removed and the product is loaded directly into the bag. Increase production by 40% by turning on the "auto" feature to cycle the bagger on the trailing edge of the light curtain input signal. Lockout key is provided to prohibit by-passing safety feature. Excellent option for hand loading operations. Learn More
  5. Medical Seal Validation Assembly

    Medical Seal Validation Assembly

    Product Code:
    • TO-T1-MV
    Validates settings and prevents cycle operation if parameters are not within the range of acceptance. Learn More
  6. Quick Roll Change

    Quick Roll Change

    Product Code:
    • TO-T1-QC
    Additional roll shaft and chucks. By having a full roll shafted, the operator can perform roll changes quickly and immediately when the bagger is out of bags. Learn More
  7. T-1000 Stacked Lights

    T-1000 Stacked Lights

    Product Code:
    • TO-T1-SL
    LED light assemblies to alert operator that system is stopped or in a fault condition (ie: out of bags, out of ribbon, preset count reached, product jam, funnel jam, misfeed or other machine fault condition) and also a general warning condition (ie: parts flow interruption, low on parts or materials or other warning). Note: LEDs conditions may change based on the type of system and indicated errors. Learn More
  8. T-1000 Stainless Steel Upgrade

    T-1000 Stainless Steel Upgrade

    Product Code:
    • TO-T1-SS
    Upgrade to the stainless steel for medical applications or food applications. Learn More
  9. Concave Load Shelf

    Concave Load Shelf

    Product Code:
    • TO-T1-LSC
    Supports the bottom/ back of bag during loading of heavier or bulkier products. Pneumatically operated, adjustable shelf provides support and takes initial impact of heavier products dropping in the bag. Shelf tilts downward after sealing, dropping product from shelf. Various lengths for longer bag sizes. Learn More
  10. Load Shelf

    Load Shelf

    Product Code:
    • TO-T1-LS10
    Supports the bottom/ back of bag during loading of heavier or bulkier products. Pneumatically operated, adjustable shelf provides support and takes initial impact of heavier products dropping in the bag. Shelf tilts downward after sealing, dropping product from shelf. Various lengths for longer bag sizes. Learn More

Items 21 to 30 of 58 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

List  Grid 

Set Descending Direction