For UK service,
Please visit http://appuk.co.uk

T-1000 Options and Accessories


Options and Accessories for the T-1000

Although the T-1000 is extensively equipped with many "built in" options, a full range of auxiliary options and equipment can easily be added for special purpose packaging or to improve your packaging operation.

Funnels, Standard and Custom: Order funnels that are in stock at all times with sizes ranging from a 1" opening to a 7" opening. Custom funnels are also provided to facilitate loading. Having the proper funnel and bag size for your product is very crucial to an efficient operation.

AF-10 Accumulating Funnel: Pneumatic gate increases the speed of automatic operations by "staging" the product immediately above the bag opening. When the bag is ready to receive the product, the gate opens, enters the bag, and maintains the bag opening to reduce product spills.

CF-10 Counting Funnel: Add a photo array to the AF-10 funnel for inline bagging operations. Counts product as it enters the funnel; pneumatic funnel causes separation between counts for continuous feed operations.

LS-10 Load / Support Shelf: Supports the bottom/back of bag during loading of heavier or bulkier products. Pneumatically operated, adjustable shelf provides support and takes the initial impact of heavier products dropping into the bag. Shelf tilts downward after sealing, dropping product from the shelf. Available in various length for longer bag sizes.

LSV-10 Vibratory Shelf Attachment: "Taps" the bag to settle product to the bottom of the bag. Pneumatic operation with speed controls. LS-10 Option must be previously installed or purchased with the vibratory shelf attachment.

LC-10 Light Safety Curtain: An OSHA approved safety device that restricts the cycle operation of the bagger when the optical detection field is obstructed. LC-10 option is recommended when the funnel is removed and the product is loaded directly into the bag. Increase production by 40% by turning on the "auto" feature to cycle the bagger on the trailing edge of the light curtain input signal. Lockout key is provided to prohibit bypassing the safety feature. Excellent option for hand loading operations.

DF-10 Diverting Funnel/Bag Counting Option: As finished bags are sealed and dropped from your bagger, they can be counted and redirected at the end of each preset count. With a two box system, the bags are directed into "Box A" until the final count is reached. Then the diverter rotates, directing the bags into "Box B" allowing the operator time to remove, seal and replace "Box A". Includes diverting/rotating attachment, photo array, brackets and counter controls. (UF-2000 Incline Conveyor sold separately.)

PT-10 Partition Table Attachment: Stainless steel partitioned utility table keeps products separated for manual kit packaging. Two sizes available depending upon size and quantity of product. Adjustable tilt and height to fit over bagger

LB-10 Label Applicator Attachment: Apply preprinted labels inline while bagging. Labels are accurately dispensed onto the bag from an air vacuum grid with +/- 1/32" dispensing accuracy. Also Print and Apply labels with our thermal transfer printer/label applicator. Print up to 305dpi on labels from 1/2" x 1/2" up to 4" x 6". CD-10

Compact Disc Loader: With the CD Loader option, the T-1000 packages compact discs at a rate of up to 70 packages per minute. Package into tamper evident poly bags, either printed or nonprinted Significantly reduce packaging costs over jewel cases or sleeves.

PB-20 Dual Optical Palm Buttons: OSHA approved safety device. Two optical "no-touch" buttons must be pressed simultaneously to initiate the cycle operation of the bagger. If the two sensors are not pressed at the same time, the bagger will not cycle, ensuring that fingers or hands cannot be in the seal area. Recommended when no funnel is present.

SP-10 Level 1 Spare Parts Kit: Kit contains day to day normal wear items. PTFE sheet, filter, fuses, seal rubber, and heater cartridges identifies some items in the kit.

SP-20 Level 2 Spare Parts Kit: Additional items not projected to fail, but due to the cost of loss of production, are required to prevent downtime. Valves, cylinders, circuit boards, and a touch screen are some of items included in this kit.

FS-10 Flat Seal Assembly: Decreases the possibility of wrinkles in the seal area while increasing seal integrity. Pneumatically operated opposing "fingers" pull each side of the bag taught above the seal area to flatten the seal area.

BF-10 Bag Deflator: Removes excess air from the bag. Sponge or rubber loop deflators push the air out just prior to sealing.

BV-10 Barcode Verifier: Verifies that barcodes on preprinted or thermally printed bags are readable and stops the cycle operation when a non-readable barcode is detected.

More Options

AD-10 Point of Use Air Dryer: Filter 99% of liquids from your plant air with this dryer component. Liquids are then automatically drained before entering the pneumatic system increasing component life.

BO-10 Bag "Out" Sensor: Detects the last bag off the roll and shuts down the bagger, while alerting the operator of the fault condition.

BO-20 Bag "Open" Sensor: (AF-10 Funnel required.) Detects whether the bag has properly blown open prior to the product entering the bag.

CB-10 Compartment Seal Option: Separate two products in one bag by creating a seal between two compartments. After the first product is loaded, press the foot switch to seal the first product in the bag. Then load the second product, and press the foot switch to index the bag and seal the bag a second time above the second product. The bag is then detached and another bag is indexed into the loading position.

FD-10 Single 3-1/2" Floppy Disk Loader: With the Floppy Disk Loader option, the T-1000 packages 3-1/2" floppy disks at a rate of up to 60 packages per minute. Cartridge tray holds up to 300 floppy disks. Load floppy disks while bagging. Loader can be quickly removed to package manuals, case drivers, instruction sheets or any other loose items such as screws, keys or kits.  

IF-10 Insert Funnel: For products affected by air flow, an insert funnel provides a solution. After the bag has been blown open, the funnel enters the bag, holding it open so air can be decreased or shut off. The funnel enters past the seal area decreasing the potential of seal contamination. This is good for granular type products.

OFS-10 Output Fault Signal: Signal is provided to advise third party equipment that a fault condition (i.e.: out of bags, jam detection, printer error) is present on the T-1000 bagger and to cease production operations. Audible or visual signals can also be provided to alert the operator.

QC-10 Quick Roll Change Option: Additional roll shaft and roll chucks. By having a full roll shafted, the operator can perform roll changes quickly and immediately when the bagger is out of bags.

TS-10 Trim Seal Assembly: Trims excess film from bag above seal to enhance the appearance of the package (retail products).

TW-10 Twin-Seal Option: Automatically seals the bag a second time, 3/4" from the first seal to increase bag integrity.

VA-10 Vacuum Bag Opening Assembly: When air flow is not sufficient to open the bag, or when air cannot be used to open the bag, vacuum tips do the job. Tips protrude to the bag and retract pulling the bag open. Air flow can be shut off for products affected by air flow.

Products

Items 31 to 40 of 58 total

per page
Page:
  1. 2
  2. 3
  3. 4
  4. 5
  5. 6

List  Grid 

Set Descending Direction
  1. OFS-10 Output Fault Signal

    OFS-10 Output Fault Signal

    Product Code:
    • TO-T1-OFS10
    OFS-10 Output Fault Signal ;;Output Fault Signal provides a signal when the T-1000 is in the Stop or Fault mode. ;Includes:; Two outputs (output 1 - bagger ready/not ready, output 2 - fault/no fault). Relay output signals;. Standard open ended cable from Aux2 port with schematic drawing to assist with interface to third party equipment. Learn More
  2. LP-10 Loose Parts Diverter

    LP-10 Loose Parts Diverter

    Product Code:
    • TO-T1-LP10
    LP-10 Loose Parts Diverter ;;Loose parts, as a result of misfunneling, bouncing or bag opening issues, are directed into a reject bin. After sealing, the diverted will close and allow the bag with to feed into a takeaway conveyor separately from the loose parts, preventing contamination of previously bagged product. Also improves the operation of the US-4000 Checkweigh Scale by preventing loose parts from causing the weight to be accepted. ;Includes: Pneumatic diverter assembly;, programming enabled in T-1000; PLC. Learn More
  3. ES-10 E-Stop Switch / Controls

    ES-10 E-Stop Switch / Controls

    Product Code:
    • TO-T1-ES10
    Kit, ES-10 E-Stop Switch / Controls;;Emergency stop circuit to shut off air to moving components and prevent bagger cycle operation. Learn More
  4. DU-10 Driven Unwind Assembly

    DU-10 Driven Unwind Assembly

    Product Code:
    • TO-T1-DU10
    DU-10 Driven Unwind Assembly ;;Driven unwind stand is required for larger or heavier rolls when APPI's standard non-driven unwind does not keep consistent tension on the rolls. Features: Linear potentiometer controls the speed of the unwind motor, DC motor / drive control with forward / reverse controls, Pressure regulator to control tension. Learn More
  5. DF-20 Diverting Funnel Assembly

    DF-20 Diverting Funnel Assembly

    Product Code:
    • TO-T1-DF20
    DF-20 Diverting Funnel Assembly;;Finished (bagged) product counting and diverting system counts down from a preset number until the final count (carton count) is reached. Once the count is reached, a diverter will direct the product from box A to box B. When the next batch count is reached, the product will be diverted from box B to box A.; Features: Pneumatically operated diverting funnel assembly, single beam photo eye to detect finished bag dropping into diverting funnel;, counting option enabled in bagger PLC. **Note: UF-2000 Take-away conveyor not included; quoted separately. Learn More
  6. CF-20 Optical Frame Counting Funnel

    CF-20 Optical Frame Counting Funnel

    Product Code:
    • TO-T1-CF20
    CF-20 Optical Frame Counting Funnel ;;Programmable counting function enabled in T-1000 to count parts, then automatically initiate the bagger cycle operation when the final count is reached. For continous feeding operations, an accumulator is also required (sold separately). ;Features:; Final count from 1 to 99,999;, accurate detection of smaller components of at least 1/8", virtually no gaps in detection field, interface cables to bagger, sample PLC function, stainless steel housing to reduce light, mounting to standard funnel. **Note: Sample parts should be sent to APPI for testing to confirm photo eyes and accuracy of counts. Accumulating funnel required if continuously feeding parts. Learn More
  7. CF-10 Counting Funnel

    CF-10 Counting Funnel

    Product Code:
    • TO-T1-CF10
    CF-10 Counting Funnel ;;Programmable counting function enabled in T-1000 to count parts, then automatically initiate the bagger cycle operation when the final count is reached. For continous feeding operations, an accumulator is also required (sold separately). ;Features:; Final count from 1 to 99,999;, accurate detection of smaller components of at least 1/4", minor gaps in detection field (less than 1/4"), interface cables to bagger, sample PLC function, stainless steel housing to reduce light, mounting to standard funnel, infrared photo emitter & receiver. **Note: Sample parts should be sent to APPI for testing to confirm photo eyes and accuracy of counts. Accumulating funnel required if continuously feeding parts. Learn More
  8. CE-10 European Conformity Assembly (T-1000-S14)

    CE-10 European Conformity Assembly (T-1000-S14)

    Product Code:
    • TO-T1-CE
    CE-10 European Conformity Assembly (T-1000-S14);Kit to convert the standard (US Version) to comply with EU Safety Standards. Includes: Extended/modified guarding. Learn More
  9. CD-20 Automatic Cash Dispensor

    CD-20 Automatic Cash Dispensor

    Product Code:
    • TO-T1-CD20
    CD-20 Automatic Cash Dispensor;;Dispensor to automatically feed wrapped stacks of US Currency into the T-1000 Advanced Poly Bagger. Features: 30" tall stack accumulator / dispensor to hold up to 30, 1" stacks, low level product sensor, special product chute, product verification sensor, controlled by the T-1000 touch screen. Learn More
  10. CB-10 Compartment Seal Option

    CB-10 Compartment Seal Option

    Product Code:
    • TO-T1-CB10
    CB-10 Compartment Seal Option ;Create two compartments in the bag with this special program functionality to prevent one product scratching another for instance. After the first product is loaded, the bag is sealed and the bag is blown open a second time. After the second product is loaded, the bag feeds to the second seal point and a second seal is applied. **Note: Depending on the top compartment size, drop frame or extended drop frame configuration may be required. This may limit the bag size. Learn More

Items 31 to 40 of 58 total

per page
Page:
  1. 2
  2. 3
  3. 4
  4. 5
  5. 6

List  Grid 

Set Descending Direction